Unknown Brand

Harness the sustainable power of the sun with these solar modules from AURIA. Not only effective when facing south, they also generate stable amounts of electricity when pointing north, east or west and in bad weather. Delivered in a packing unit of 30.

PHAESUN

Phaesun has made a strong impression with this foldable solar module that includes a charge regulator and plug-in connection adapters. Designed for flexible and mobile use, it impresses with simple connection and high energy yield in the most limited space. An innovative design and low weight of only 2.5 kg, you can take all connection components with you and transport them easily. When folded in the textile frame, this module is an unobtrusive companion, quickly ready for use anywhere and easy to stow away again afterwards. The textile module support has riveted eyelets (9.5 mm inner diameter) for hanging or fixing the module, such as with rubber cord or ratlines. The module can, of course, be laid out quite simply. It also comes with set-up supports that may be used to align the module to low sun and are secured in place by Velcro straps when not in use. The outside pocket contains all connection cables (1 m module connection, 3.9 m at the input of the PHOCOS charge controller and approx. 1.4 m at the controller output), a battery temperature sensor (with 2 m connection cable) as well as 3 adapter cables for connection to the battery or to the vessel's electrical system. . The adapter cables are each 1m long and fitted with crocodile clips, ring terminals (5 mm ring inner Ø) and cigarette lighter plugs (incl. 10 A fine-wire fuse). All cables and adapters have solid and reverse polarity protected plug connections, can be rapidly plugged together as needed, and sealed against dirt and corrosion when not in use. When connected, the cable lengths between the module and the charge controller are 4.9 meters, and the cable length between the charge controller and the battery/vehicle power connection is approximately 2.4 meters. The temperature sensor of the PHOCOS charge controller is polarity-free and should be attached with its metal housing directly to a battery connection and secured using insulating tape or cable ties. The PHOCOS charge controller's 5 V USB output can power mobile devices such as smartphones, tablets, cameras, and other gadgets (max. 1500 mA). Technical data System voltage 12 V Nominal power 90 W (2x 45 W) Current at max. power 4.3 A Operating temperature -10 °C to +60 °C Frame Textile Module/Battery/Adapte cable 4000 mm / 1000 mm / 1500 mm - 2,5 mm² Dimensions unfolded 1075 x 560 x 8 mm Dimensions folded 440 x 560 x 15 mm Weight: 2.5 kg Charge controller system voltage / max. solar power 12 V DC / 10 A USB output power charge controller 5 V DC / 1500 mA Certificates CE, RoHS Notes When using the crocodile clip adapter or the lug adapter, we also recommend installing a 10 A fuse close to the battery (max. 20 cm). Fuse holders, fuses and crimp cable connectors are available separately. For the ring terminal adapter, crimp ring terminals with larger ring inner Ø are available separately. All connection and adapter cables are 14 AWG (American Wire Gauge), which corresponds to approx. 2.5 mm². Although the PHOCOS charge controller used is automatically capable of recognising 12 or 24 volt battery systems, the module can only be used in 12 volt wiring systems due to the 20.9 volt Vmp output voltage. The controller is not splashproof and must therefore be housed in a dry environment! Due to the plug connection on the module connection cable, you can also permanently install the controller. To fix the controller, two 4 mm screws are required, which can be inserted/screwed through the controller housing from the front. The distance between the holes is 69 mm or 57 mm to the top edge of the housing. The USB output can only be used when the 12 V battery is connected. Please refer to the operating instructions for further technical information on the controller. Instructions can be found below under Documents. Please observe the instructions in the operating manual of the controller! If the charge controller is to be permanently installed in the vehicle with battery negative to ground, module negative and consumer negative connections must only be connected to the NEGATIVE terminals of the charge controller and must never be connected to vehicle ground or bridged in any way. Otherwise the deep discharge protection and overcurrent protection of the charge controller would be bypassed.

PHAESUN

Phaesun has made a strong impression with this foldable solar module that includes a charge regulator and plug-in connection adapters. Designed for flexible and mobile use, it impresses with simple connection and high energy yield in the most limited space. An innovative design and low weight of only 5.6 kg, you can take all connection components with you and transport them easily. When folded in the textile frame, this module is an unobtrusive companion, quickly ready for use anywhere and easy to stow away again afterwards. The textile module support has riveted eyelets (9.5 mm inner diameter) for hanging or fixing the module, such as with rubber cord or ratlines. The module can, of course, be laid out quite simply. It also comes with set-up supports that may be used to align the module to low sun and are secured in place by Velcro straps when not in use. The outside pocket contains all connection cables (1 m module connection, 3.9 m at the input of the PHOCOS charge controller and approx. 1.4 m at the controller output), a battery temperature sensor (with 2 m connection cable) as well as 3 adapter cables for connection to the battery or to the vessel's electrical system. The adapter cables are each 1m long and fitted with crocodile clips, ring terminals (8 mm ring inner Ø) and cigarette lighter plugs (incl. 10 A fine-wire fuse). All cables and adapters have solid and reverse polarity protected plug connections, can be rapidly plugged together as needed, and sealed against dirt and corrosion when not in use. When connected, the cable lengths between the module and the charge controller are 4.9 meters, and the cable length between the charge controller and the battery/vehicle power connection is approximately 2.4 meters. The temperature sensor of the PHOCOS charge controller is polarity-free and should be attached with its metal housing directly to a battery connection and secured using insulating tape or cable ties. The PHOCOS charge controller's 5 V USB output can power mobile devices such as smartphones, tablets, cameras, and other gadgets (max. 1500 mA). Technical data System voltage 12 V Nominal power 135 W (3x 45 W) Spannung bei max. leistung (Vmp) 22.6 V Current at max. power (Imp) 6 A Open circuit voltage (Uoc) 26 V Short circuit current (Isc) 6.4 A Cells / Cell efficiency 3x 12 mono / 23.9 % Operating temperature -10 °C to +60 °C Frame Textile Module/Battery/Adapte cable approx. 4000 mm / 1500 mm / 1000 mm - 14 AWG or, approx. 2.5 mm² Dimensions unfolded 1525 x 560 x 10 mm Dimensions folded 440 x 560 x 20 mm Weight: 5.6 kg Charge controller type / system voltage / max. solar current PWM with LCD display / 12 V DC / 10 A USB output power charge controller 5 V DC / 1500 mA Certificates CE, RoHS Notes When using the crocodile clip adapter or the lug adapter, we also recommend installing a 10 A fuse close to the battery (max. 20 cm). Fuse holders, fuses and crimp cable connectors are available separately. For the ring terminal adapter, crimp ring terminals with larger ring inner Ø are available separately. All connection and adapter cables are 14 AWG (American Wire Gauge), which corresponds to approx. 2.5 mm². Although the PHOCOS charge controller used is automatically capable of recognising 12 or 24 volt battery systems, the module can only be used in 12 volt wiring systems due to the 22.6 volt Vmp output voltage. The controller is not splashproof and must therefore be housed in a dry environment! Due to the plug connection on the module connection cable, you can also permanently install the controller. To fix the controller, two 4 mm screws are required, which can be inserted/screwed through the controller housing from the front. The distance between the holes is 69 mm or 57 mm to the top edge of the housing. The USB output can only be used when the 12 V battery is connected. Please refer to the operating instructions for further technical information on the controller. Instructions can be found below under Documents. Please observe the instructions in the operating manual of the controller! If the charge controller is to be permanently installed in the vehicle with battery negative to ground, module negative and consumer negative connections must only be connected to the NEGATIVE terminals of the charge controller and must never be connected to vehicle ground or bridged in any way. Otherwise the deep discharge protection and overcurrent protection of the charge controller would be bypassed.

PHAESUN

Phaesun has made a strong impression with this foldable solar module that includes a charge regulator and plug-in connection adapters. Designed for flexible and mobile use, it impresses with simple connection and high energy yield in the most limited space. An innovative design and low weight of only 5.6 kg, you can take all connection components with you and transport them easily. When folded in the textile frame, this module is an unobtrusive companion, quickly ready for use anywhere and easy to stow away again afterwards. The textile module support has riveted eyelets (9.5 mm inner diameter) for hanging or fixing the module, such as with rubber cord or ratlines. The module can, of course, be laid out quite simply. It also comes with set-up supports that may be used to align the module to low sun and are secured in place by Velcro straps when not in use. The outside pocket contains all connection cables (1 m module connection, 3.9 m at the input of the VICTRON charge controller and approx. 1.4 m at the controller output), as well as 3 adapter cables for connection to the battery or to the vessel's electrical system. The adapter cables are each 1m long and fitted with crocodile clips, ring terminals (8 mm ring inner Ø) and cigarette lighter plugs (incl. 10 A fine-wire fuse). All cables and adapters have solid and reverse polarity protected plug connections, can be rapidly plugged together as needed, and sealed against dirt and corrosion when not in use. When connected, the cable lengths between the module and the charge controller are 4.9 meters, and the cable length between the charge controller and the battery/vehicle power connection is approximately 2.4 meters. Technical data System voltage 12 V Nominal power 135 W (3x 45 W) Voltage at max. power (Ump) 22.6 V Current at max. power (Imp) 6 A Open circuit voltage (Uoc) 26 V Short circuit current (Isc) 6.4 A Cells / Cell efficiency 3x 12 mono / 23.9 % Operating temperature -10 °C to +60 °C Frame Textile Module/Battery/Adapte cable approx. 4000 mm / 1500 mm / 1000 mm - 14 AWG or, approx. 2.5 mm² Dimensions unfolded 1525 x 560 x 10 mm Dimensions folded 440 x 560 x 20 mm Weight: 5.6 kg Charge controller type / system voltage / max. solar current MPPT / 12/24 V / 10 A / VE.direct / Bluetooth Certificates CE, RoHS Notes When using the crocodile clip adapter or the lug adapter, we also recommend installing a 10 A fuse close to the battery (max. 20 cm). Fuse holders, fuses and crimp cable connectors are available separately. For the ring terminal adapter, crimp ring terminals with larger ring inner Ø are available separately. All connection and adapter cables are 14 AWG (American Wire Gauge), which corresponds to approx. 2.5 mm². Although the VICTRON charge controller used is automatically capable of recognising 12 or 24 volt battery systems, the module can only be used in 12 volt wiring systems due to the 22.6 volt Vmp output voltage. If the charge controller is to be permanently installed in the vehicle with battery negative to ground, module negative and consumer negative connections must only be connected to the NEGATIVE terminals of the charge controller and must never be connected to vehicle ground or bridged in any way. Otherwise the deep discharge protection and overcurrent protection of the charge controller would be bypassed.

SUNWARE

The FOX-062 is a highly modern miniature-charge regulator for 12 V and 24 V solar systems. Even though it is small in size, the overcharge protection is designed for a solar current of 6.6 A. This corresponds to 120 Wp max. solar power at 12 V or 240 Wp at 24 V. Reverse current protection is integrated. The charging characteristic can be set for lead-acid, GEL, LiFePO4 or AGM batteries using the red DIP switch in the controller housing. The opening can be closed with a slide, making accidental change and dirt entry impossible. A protective SureSeal socket is located on the input end, into which a SureSeal plug can be inserted. On the output end towards the batteries, there is a car plug connector with integrated safety. When the red adapter is switched off, the car connector can also be used. Delivery includes 1m cable 2x1.5 mm² with SureSeal plug on one end, This allows each module to be directly connected to the charge controller. Note: Modules with a maximum output of 120 Wp can be connected to this charge controller in a 12 V on-board network. In a 24 V on-board network, the maximum module output must not exceed 240 Wp. Technical Data 12 V / 24 V system voltage 6.6 A max. solar power (lsc) 120 watts solar power at 12 V 240 watts solar power at 24 V Suitable module voltages for 12V systems: Open circuit voltage Uoc > 16V and < 24V Voltage at maximum power Ump > 14V and < 20V Suitable module voltages for 24V systems: Open circuit voltage Uoc > 32V and < 48V Voltage at maximum power Ump > 28V and < 40V Battery type adjustable via DIP switch to lead-acid, AGM, gel or LiFePO4 batteries Charging voltage Lead acid 14.4 V AGM 14.5 V Gel 14.3 V LiFePO4 14.6 V Trickle charge 13.8 V Multi-colour LED indicator High charging efficiency This charge controller is designed as a series controller with active reverse current protection. A charging degree effectiveness of 98% is achieved. In contrast to MPPT regulators, this regulator type has a up to 20% higher charging performance while using 12 V or 24 V solar modules. High converter losses are fully avoided. This series controller really stands out in very low lighting; in a normal MPPT regulator, losses would strongly influence the flow rate. Since the FOX - 062 has no leakage, no cooler is necessary. Der beste Beweis für optimales Layout der Schaltung. Automatic 12 V / 24 V recognition After plugging in the controller, the controller checks the current battery voltage and thereby determines the system voltage of the battery. No settings need to be made for this. The controller will not start if the battery voltage is less than 8.6 V for safety reasons, as the battery may be defective. LED display The FOX-062 is equipped with a three-colour LED. A variety of information regarding the battery and charge can be presented by combining the LED colours and adjusting the light duration or flashing frequency: Flashing red: battery empty (< 20 %) Constant red: battery low (< 30 %) Orange: battery normal (30% - 70 %) Constant green: battery normal (> 70 %) Flashing green: battery full (100 %) When charging current is flowing from the solar module into the battery, the LED flickers briefly every few seconds. If the plug is pulled out of the socket, the LED goes off - even if a solar module is connected. Made in Germany! All SunWare products are developed, tested and produced in Germany. The front cover of the modules are also made in Germany. By doing this, the high quality requirements of our products and materials can also be guaranteed. On request, extension cables with SureSeal plug and socket are available in 5 or 10 m lengths.

SUNWARE

The FOX-220 solar charge controller is suitable for AGM, GEL and lead-acid batteries. Consumers can be connected up to a current consumption of 22 A maximum. The optimised charge characteristic curve in combination with the hardware PWM control achieves a distinctly faster and gentler charging of the battery; hazardous gassing or overcharging are safely prevented. The adaptive total discharge protection monitors and protects the battery against damaging total discharge. The controller recognises fully automatically whether a 12 V or 24 V battery system is connected. The Multi Display FOX-MD1 can be connected to the charge controller at any time with a simple plug-in. This enables the display of current voltages and flows, even graphically. The FOX-programming MD1's function allows you to change and save various parameters. Features: PWM solar controller For 1 battery bank 12 / 24 V auto detection Overcharge protection and deep discharge protection Installation: flush Nominal PV power: 12 V up to 380Wp 24 V up to 760Wp Made in Germany! All SunWare products are developed, tested and produced in Germany. The front cover of the modules are also made in Germany. By doing this, the high quality requirements of our products and materials can also be guaranteed.

SUNWARE

The FOX-260 V2.1 is suitable for surface mounting and can be connected to solar modules of all makes. The charge controller can be used for AGM, gel, lead-acid and lithium (LiFePO4) batteries. No switching required. The gentle 3-stage charging characteristic contributes to increasing the performance and service life of your battery significantly. In addition, the LC display provides you with clear information about the current system status of your solar system at all times: charging/discharging current and voltage of the batteries is displayed to you at the touch of a button. Features: PWM solar controller Designed for 1 battery bank 12 / 24 V auto detection Reverse current protection Overcharge protection and deep discharge protection Manual setting of the end-of-charge voltage and the load cut-off voltage Backlighting of the display and a night light function Surface mount Nominal PV power: 12 V up to 400 Wp 24 V up to 800 Wp Made in Germany! All SunWare products are developed, tested and produced in Germany. The front cover of the modules are also made in Germany. By doing this, the high quality requirements of our products and materials can also be guaranteed.

SUNWARE

The FOX-320 solar charge controller is suitable for AGM, GEL and lead-acid batteries. Consumers can be connected up to a current consumption of 22 A maximum. The optimised charge characteristic curve in combination with the hardware PWM control achieves a distinctly faster and gentler charging of the battery; hazardous gassing or overcharging are safely prevented. Two battery systems can be charged with the FOX-320. From the factory, 90% of the energy is charged in battery 1 and 10% of the energy in battery 2. The adaptive total discharge protection monitors and protects the battery against damaging total discharge. The controller recognises fully automatically whether a 12 V or 24 V battery system is connected. The Multi Display FOX-MD1 can be connected to the charge controller at any time with a simple plug-in. This enables the display of current voltages and flows, even graphically. The FOX-programming MD1's function allows you to change and save various parameters. Features: PWM solar controller For 2 battery banks 12 / 24 V auto detection Overcharge protection and deep discharge protection Installation: flush Nominal PV power: 12 V up to 380Wp 24 V up to 760Wp Made in Germany! All SunWare products are developed, tested and produced in Germany. The front cover of the modules are also made in Germany. By doing this, the high quality requirements of our products and materials can also be guaranteed.

SUNWARE

The FOX-360 V2.1 is suitable for surface mounting and can be connected to solar modules of all makes. The charge controller can be used for AGM, gel, lead-acid and lithium (LiFePO4) batteries and can be connected to 2 batteries at the same time. No switching required. The gentle 3-stage charging characteristic contributes to increasing the performance and service life of your battery significantly. In addition, the LC display provides you with clear information about the current system status of your solar system at all times: charging/discharging current and voltage of the batteries is displayed to you at the touch of a button. Features: PWM solar controller Designed for 2 battery banks 12 / 24 V auto detection Reverse current protection Overcharge protection and deep discharge protection Manual setting of the end-of-charge voltage and load cut-off voltage Backlighting of the display and a night light function Surface mount Nominal PV power: 12 V up to 400 Wp 24 V up to 800 Wp Made in Germany! All SunWare products are developed, tested and produced in Germany. The front cover of the modules are also made in Germany. By doing this, the high quality requirements of our products and materials can also be guaranteed.

PHAESUN

The thin and light MARE FLEX 120 solar module delivers a maximum output of 120 Wp, is bendable and perfect for installing on sailing yachts and motor boats as well as on the roofs of caravans and trucks. It is also ideal for use in mobile applications, such as outdoor activities and camping. The front and back foil is made of ETFE and is weatherproof, yet extremely translucent. The module is particularly easy to install: It can either be fixed in place with construction adhesives (e.g. SIKA 291) or by using the integrated stainless steel eyelets. The solar module is supplied with a 5 m long connection cable with 2 x 2.5 mm² cable heads. Features Discover the features that make this product stand out. From technical details to special functions – we’ve summarized all the key information for you. Construction type Semi-flexible Connector None Module connection Front side Connector cable Round (multi-core)

PHAESUN

The MARE FLEX 155 is a thin and light solar module that delivers a maximum output of 155 Wp. The module is bendable and perfect for installing on sailing yachts and motor boats as well as on the roofs of caravans and trucks. It is also ideal for use in mobile applications, such as outdoor activities and camping. The front and back foil is made of ETFE and is weatherproof, yet extremely translucent. The module is particularly easy to install: It can either be fixed in place with construction adhesives (e.g. SIKA 291) or by using the integrated stainless steel eyelets. The solar module is supplied with a 5 m long connection cable with 2 x 2.5 mm² cable heads. Note The open-circuit voltage (Uoc or Voc) of this powerful module is 31.2 V. Make sure that the charge controller has sufficient dielectric strength! MPP or MPP CI series Votronic controllers can be used with this solar panel without issue. Votronic SR series charge controllers are unsuitable for this module, as they are only designed for a max. no-load voltage of 28 volts. Features Discover the features that make this product stand out. From technical details to special functions – we’ve summarized all the key information for you. Construction type Semi-flexible Connector None Module connection Front side Connector cable Round (multi-core)

PHAESUN

The thin and light MARE FLEX 55 solar module delivers a maximum output of 55 Wp, is bendable and perfect for installing on sailing yachts and motor boats as well as on the roofs of caravans and trucks. It is also ideal for use in mobile applications, such as outdoor activities and camping. The front and back foil is made of ETFE and is weatherproof, yet extremely translucent. The module is particularly easy to install: It can either be fixed in place with construction adhesives (e.g. SIKA 291) or by using the integrated stainless steel eyelets. The solar module is supplied with a 5 m long connection cable with 2 x 1.5 mm² cable heads. Features Discover the features that make this product stand out. From technical details to special functions – we’ve summarized all the key information for you. Construction type Semi-flexible Connector None Module connection Front side Connector cable Round (multi-core)

SUNBEAM

This compact mini MPPT charger is ideal for mobile use, whether on board or when camping. The MPPT technology ensures that the maximum module output can be utilised in the vehicle electrical system or stored in the battery. The standardised 2-pin SAE plug connections of the charge controller and the adapter cables included in the delivery contents make connecting the solar module, Mini-MPPT and on-board power supply or battery child's play. The Mini-MPPT works with an advanced 4-stage charging characteristic. Settings can be made via a multifunction button. The controller can be set to charge standard lead-acid/AGM**, GEL or LiFePO4 batteries with just a few presses of a button. The function button also activates a small, innovative LC display and shows you all relevant information about the charging process, such as battery voltage, charging current, device temperature (°C & °F) and error codes. The display switches off automatically approx. 20 seconds after the last button is pressed. Other small LEDs continue to operate and indicate the charging progress and the selected battery type. The regulator is protected against overcharging, overheating and reverse polarity. The following accessories are included: 1x solar module connection adapter (2x 18AWG***) with SAE and MC4 connectors, length approx. 20 cm 1x extension cable (2x 18AWG) with 2 SAE plugs, length approx. 100 cm 1x battery connection cable (2x 18AWG) with crocodile clips, length approx. 100 cm 1x vessel electrical system connection cable with cigarette lighter plug, length approx. 100 cm, A red indicator LED and an F15A miniature fuse (6.3x32 mm) are integrated in the cigarette lighter plug 1x elastic protective cover Technical Data Battery voltage 12 V Maximum charging current 10 A Maximum PV power 140 W Maximum PV open-circuit voltage 30 V Recommended battery capacity < 300 Ah (otherwise significantly longer charging time with higher capacity) Operating temperature -30 to +50 ° C Self-consumption 9 mA (15 mA with backlight on) Charge algorithm 4-stage, CC/boost, CV/absorption, float/maintenance, cell equalisation/desulphation**, Protection category IP45 Dimensions (h x w x d) 102 x 65 x 27 mm Weight 170 g ** With a permanent connection to the battery, the charging voltage is increased to 14.6 V every week with the STD characteristic curve in order to bring the battery cells to the same state of charge or to desulphate them. Check whether 14.6 V is suitable for your AGM battery. This weekly voltage increase does not occur with the GEL characteristic curve. *** 18 AWG = 0.823 mm², you should select a larger cable cross-section for possible extensions. Operation Briefly pressing the multifunction button activates the LC display. Additional short button presses enable you to choose between displaying the battery voltage/charging current, the temperature of the Mini-MPPT or the error codes. Pressing and holding the multifunction button activates the mode for setting the battery characteristic curve. Further long button presses are used to select between STD (standard lead acid) GEL or LFP (LiFePO4). Small LEDs signal the set battery type. Battery type GEL STD LFP (LiFePO4) Boost Charge Voltage 14.2 V 14.4 V 14.4 V Float Charge Voltage 13.8 V 13.8 V No float charge Equalizing Charge Voltage No EQ 14.6 V No EQ Boost Charge Recovery Voltage 13.2 V 13.2 V - Over-Discharge Recovery Voltage 12.6 V 12.6 V 12.6 V Over-Discharge Voltage 11.1 V 11.1 V 11.1 V Temperature Compensation (12 V Battery) -3 mV per 2 V cell at 1 Kelvin temperature difference -18mV/K -18mV/K No temperature compensation Error codes Error code Error E00 No error E01 Deep discharge E02 Battery overvoltage E06 Charge controller is overheated E10 Solar overvoltage E13 Solar input connected with reversed polarity E16 Battery connected with reverse polarity If an error code is displayed, you should disconnect the charge controller from the PV module and the battery, rectify the error and then re-establish the connections. Note Individual parts of the accessories supplied are not available as spare parts.

SUNBEAM

Optimised for use on yachts and motorhomes! Thanks to the MPPT technology, you can gain maximum energy with the MoonRay charge controllers even in cloudy weather or when panels are shaded. Perfectly suited for individual or parallel solar modules. Can also be used for 24 V systems. MoonRay chargers start to charge the battery as soon as the voltage at the solar panel is 0.1 V higher than the battery voltage. This ensures maximum output during daily sunlight variations, even in very cloudy periods. Another advantage is the flat efficiency curve, so that even in changeable conditions, all the energy is always drawn from the modules and stored. Furthermore, if you wish to install several solar panels, it is possible to combine multiple MoonRays. With the optional Bluetooth dongle and the free app, you can display all controllers in a single overview, but it is also possible to display only the data of one specific controller. The charge controllers are fully configurable and most settings can be done via the integrated LCD display. This allows you to set charging characteristics for lead-acid and gel batteries via the built-in display. However, to be able to set charging profiles for AGM and lithium batteries, either the optional display or the app is required. The optional Bluetooth dongle is required to use the app. Technical specifications: Battery voltage 12/24 V Rated charge current 10 A Nominal PV power 12 V: 160 W 24 V: 320 W Maximum open circuit PV voltage 45 V Operating temperature -25 to +50 °C Maximum efficiency 97.9 % Self-consumption 13 mA Charge algorithm 4-stage load current 10 A Power terminals 4 mm² Protection category IP33 (housing) Dimensions (h x w x d) 175 x 143 x 48 mm Weight 0.57 kg Standards EN/IEC 62109-1, EN61000-6-3/EN61000-6-1, 47 CFR Part 15, Subpart B, IEC62509, IEC62321-3-1

SUNBEAM

Optimised for use on yachts and motorhomes! Thanks to the MPPT technology, you can gain maximum energy with the MoonRay charge controllers even in cloudy weather or when panels are shaded. Perfectly suited for individual or parallel solar modules. Can also be used for 24 V systems. MoonRay chargers start to charge the battery as soon as the voltage at the solar panel is 0.1 V higher than the battery voltage. This ensures maximum output during daily sunlight variations, even in very cloudy periods. Another advantage is the flat efficiency curve, so that even in changeable conditions, all the energy is always drawn from the modules and stored. Furthermore, if you wish to install several solar panels, it is possible to combine multiple MoonRays. With the optional Bluetooth dongle and the free app, you can display all controllers in a single overview, but it is also possible to display only the data of one specific controller. The charge controllers are fully configurable and most settings can be done via the integrated LCD display. This allows you to set charging characteristics for lead-acid and gel batteries via the built-in display. However, to be able to set charging profiles for AGM and lithium batteries, either the optional display or the app is required. The optional Bluetooth dongle is required to use the app. Technical specifications: Battery voltage 12/24 V Rated charge current 20 A Nominal PV power 12 V: 320 W 24 V: 640 W Maximum open circuit PV voltage 45 V Operating temperature -25 to +50 °C Maximum efficiency 98.3 % Self-consumption 14 mA Charge algorithm 4-stage load current 20 A Power terminals 6 mm² Protection category IP33 (housing) Dimensions (h x w x d) 217 x 158 x 56.5 mm Weight 0.96 kg Standards EN/IEC 62109-1, EN61000-6-3/EN61000-6-1, 47 CFR Part 15, Subpart B, IEC62509, IEC62321-3-1

MASTERVOLT

The Mastervolt MPPT charge regulator is designed using innovative technology to increase the efficiency of your solar panels. The SCM25 MPPT is compatible with all battery types, including lithium-ion batteries. The charging profiles for all types of batteries are pre-programmed and can be selected at the push of a button. The regulator is quiet and features an extremely user-friendly, clear display. Designed with safety at the forefront, the device includes built-in protection against overload, high/low battery voltage, overheating, short circuits and reverse polarity. It also comes in a robust casing with IP23 protection against condensation. Further features at a glance MPPT technology Automatic 12V / 24V detection Large and bright display Flexible charging characteristics Capacity for solar panel configurations from 200 to 700 Wp Up to 30 % faster charging compared with PWM technology Integrated battery temperature sensor Audio signal in case of malfunctions Technical Data Battery voltage 12/24 V Max. charge current 25 A Nominal PV power 360 Wp @ 12 V 720 Wp @ 24 V Max. open circuit PV voltage 75 V Power consumption 5 mA Peak static power conversion efficiency >98 % Battery types AGM, Gel, Wet, Lithium-ion Cable size max. 10 mm² LCD display Yes Lithium-ion protection Yes Battery temperature sensor Yes Alarms Buzzer Cooling Passive Waterproof IP23 Temperature range -20 to +55 °C Dimensions 135 x 190 75 mm Weight: 1.3 kg

SUNBEAM

The NORDIC series from SUNBEAMSYSTEM was specially developed for use in northern climates. It offers a universal solution for applications with a requirement for lightweight, flexible, and compact solar panels. Because they are more efficient than standard glass solar panels you’ll get higher production from a relatively small size. All NORDIC models feature the unique Shadow Optimized technology for improved performance in partial shading. The Nordic models have a smooth surface that is not scratch-resistant but can occasionally be walked on with clean shoes. Not designed to be walked upon intensively. Details Semi-flexible, i.e. can be fitted to a curved surface once during installation. Can be walked on if it is mounted/glued firmly over the entire surface on a stable, load-bearing base. 70 cm long PLUS and MINUS connection cables, pre-assembled with standard 4 solar connectors. Integrated bypass diode in the connection box. 3 mm thick Low weight Fixing eyelets: 6 x 5 mm inner Ø Our hints and tips In the SUNBEAMsystem installation manual provided, you will find all the relevant information on correct module selection, mounting and electrical installation. You will also find a quick guide with lots of relevant information in our download section. PLEASE NOTE: Only SIKASIL WS605S, SIKAFLEX 298FC or ZETTEX MS POLYMER 25 is approved for bonding the modules Please check the solar modules after receiving the goods or before installing the panels. SUNBEAMSYSTEM Nordic modules are designed by the manufacturer exclusively for use in northern climates (North Sea / Baltic Sea). It is therefore not advisable to use them in hot regions. Wir empfehlen dort die Verwendung von SUNBEAMSYSTEM Modulen aus der TF-Serie. The Nordic modules are fitted with metal eyelets. Do not drill any additional holes in the laminate and only use these eyelets to screw the modules in place. Failure to do so may result in delamination and water penetration. Never place large modules directly on a bimini. Movement of the textile surface caused by the wind will lead to the modules being repeatedly and frequently deflected, which can lead to serious power losses and even breakage of the internal cell connections and thus to premature failure of the modules. Caution: Failure to observe the above points will result in loss of warranty. Our installation tip: All semi-flexible modules are normally subject to a certain thermal expansion, which should be taken into account during installation in order to avoid unnecessarily straining the laminate at the fixing points. In order to leave enough room for thermal expansion, we recommend the use of large washers or V4A washers and max. 4 mm screws. On request, suitable white plastic rosettes are also available in sets of 10 (Li364#30106030). A matching connector set or 1 m long solar connection cables are optionally available for the modules. When selecting the connection cables, make sure that the cable cross-sections are large enough to keep the voltage losses on the cable path between the solar module and the charge controller as low as possible (< 2%)! Only Tough and Carbon modules can be installed in series, with a maximum of two modules! Maxa and Nordic modules are not suitable for serial connection. Only modules of the same exact model can be connected in series. Features Discover the features that make this product stand out. From technical details to special functions – we’ve summarized all the key information for you. Construction type Semi-flexible Connector Standard-4 (MC-4) Module connection Front side Connector cable 2 single cables Walkable

PHAESUN

The CML-USB-10 can process solar input voltages of up to 30 V and currents up to 10 A and is particularly suitable for smaller solar systems. Thanks to its IU charging characteristic it is suitable for all common 12 volt batteries with lead/acid technology (also AGM and GEL). Featuring a charging output and deep discharge protection for devices such as lights, coolers, etc. Max. charge/load current 10 A or 120 watts. The integrated USB port supplies 5 V for small devices such as mobile phones and tablets, with a current consumption of max. 700 mA. Battery charge level indication via 3 LEDs 4-stage PWM control Load cut-off advance warning by audible signal Boost, equalisation and trickle charging USB charging output for mobile devices Installation note If this charge controller is installed in a vehicle in which the battery minus is connected to the vehicle earth, neither the solar module nor the loads connected to the controller must have any connection to the vehicle earth. Otherwise the deep discharge protection and overcurrent protection of the charge controller would short circuit. Earthing the charge controller is only possible via the PLUS connections. Technical data Battery voltage 12/24 V Max. Charge/load current 10 A Trickle charge 13.8 / 27.6 V (25 °C) Main charge 14.4 / 28.8 V (25 °C), 0.5 hrs (daily) Boost charge 14.4 / 28.8 V (25°C) for 2 hrs activation: Battery voltage < 12.3 / 24.6 V Equalising charge 14,8 / 29,6 V (25 °C) für 2 h Aktivierung: 14.8 / 29.6 V (25 °C) for 2 hrs activation: Battery voltage < 12.1 / 24.2 V (min. every 30 days) Deep discharge protection 11.4 - 11.9 V / 22.8 - 23.8 V (by state of charge) 11 / 22 V (by voltage) Reactivation voltage 12.8 / 25.6 V Overvoltage cut-off 15.5 / 31 V Undervoltage cut-off 10.5 / 21 V Max. PV voltage 30 / 50 V Temperature compensation -24 mv/K (12 V); -48 mv/K (24 V) Consumption < 4 mA Grounding Common positive pole Ambient temperature -40 - +45 °C Max. Altitude 4000 m above sea level NN Battery type Lead/acid, AGM, GEL USB charging port USB Type A, 5 V, 700 mA Max. cable cross section 16 mm² (AWG 6) Protection IP20 Dimensions (L x W x H) 80 x 100 x 32 mm Weight: 0.16 kg Compliance CE compliant, RoHS compliant

Unknown Brand

The waterproof PHOCOS Eco 10 PWM charge controller can be used with solar input voltages of up to 30 V and currents of up to 10 A. Thanks to its IU charging characteristic it is suitable for all common 12 volt batteries with lead/acid technology (also AGM and GEL). Featuring a charging output and deep discharge protection for devices such as lights, coolers, etc. Max. charge/load current 10 A or 120 watts. Housing waterproof according to IP68, connections IP21. For connection cables up to max. 10 mm². Installation note If this charge controller is installed in a vehicle in which the battery negative is connected to the vehicle ground, neither the solar module nor the loads connected to the controller must have any connection to the vehicle ground. Otherwise the deep discharge protection and overcurrent protection of the charge controller would short circuit. Grouding the charge controller is only possible via the POS connections.

SUNWARE

Plug & Play SunWare solar panels. Lay down the solar module, insert the charger - done! The RX solar panels are simply plugged into a 12 V socket or cigarette lighter with the accompanying FOX-062 charger. Your battery will begin charging straight away. The panels have a 5m supply line, which allows you to park your vehicle in the shade, while the solar panel effectively generates electricity from the sun. If 5 m is not sufficient, an optional extension cable can also be connected. Mounting lugs have been placed into the textile edges of the panel with an inner diameter of 9 mm. This means you have countless mounting options with rope, cables, hooks, etc. Due to the foldable design, the modules can be easily stowed away or transported. The cells are protected against breakage by their slightly flexible aluminum carrier plate. Can be used with AGM, GEL and lead-acid batteries. Made in Germany! All SunWare products are developed, tested and produced in Germany. The front foil of the panels also comes from Germany. In doing this, the high quality requirements of the product and the materials used can be ensured. Features Discover the features that make this product stand out. From technical details to special functions – we’ve summarized all the key information for you. Construction type Foldable Connector SureSeal Module connection Front side Connector cable Round (multi-core)

SUNBEAM

SUNBEAMsystem Tough Flush (TF) solar modules are a reliable source of energy even under the harshest conditions thanks to the highly efficient SUNPOWER cells (22.5% efficiency). Due to their impressive technical properties, the Tough-Flush modules are often used in the yacht and caravan sector, as well as in private and industrial off-grid systems. The surface of these modules is extremely durable and resistant to high UV radiation. The material has a better light transmission than conventional materials. When partially shaded, the physical cell arrangement ensures a higher output power than other modules. The surface structure improves power generation at low light incidence angles and has anti-slip properties. Assembly is extremely easy. The modules can be glued with SIKA 291 and / or screwed using existing stainless steel eyelets. Special features of this module type The semi-flexible flush modules, which are only 3 mm thin, feature no obstacles or tripping hazards on the module surface because there is no junction box. This is the only type of module that can be mounted almost flush with the surface (flush mount)! Electrical connection from the back of the module is via an inconspicuous flat, white double-webbed cable (2x 1.6 mm²/approx. 1000 x 5.5 x 2.5 mm) and the cable can be attached almost invisibly next to the module on white surfaces/mounting surfaces. Details at a glance Semi-flexible High level of efficiency Durable and UV-resistant Small size & high performance Improved yield in partially shaded areas Yield enhancing, anti-slip surface structure Flush mounting (no annoying connection box on the module surface) Special technical feature of flush modules Because the connecting cables of the flush modules run directly out of the back of the module, there are no integrated blocking / bypass diodes on these modules. (For modules with a connection box, these are usually integrated in the connection box.) Technical specifications Type T111F Max. power (Pmax) 111 W Open circuit voltage (Uoc) 21.76 V Short circuit current (Isc) 6.32 A Nominal voltage (Ump) 18.56 V Nominal current (Imp) 5.97 A Weight 2.6 kg Dimensions (L x W x H) 1060 x 540 x 3 mm MoonRay160 charge regulator: Optimised for use on yachts and motorhomes! Thanks to the MPPT technology, you can gain maximum energy with the MoonRay charge controllers even in cloudy weather or when panels are shaded. Perfectly suited for individual or parallel solar modules. Can also be used for 24 V systems. MoonRay chargers start to charge the battery as soon as the voltage at the solar panel is 0.1 V higher than the battery voltage. This ensures maximum output during daily sunlight variations, even in very cloudy periods. Another advantage is the flat efficiency curve, so that even in changeable conditions, all the energy is always drawn from the modules and stored. Furthermore, if you wish to install several solar panels, it is possible to combine multiple MoonRays. With the optional Bluetooth dongle and the free app, you can display all controllers in a single overview, but it is also possible to display only the data of one specific controller. The charge controllers are fully configurable and most settings can be done via the integrated LCD display. This allows you to set charging characteristics for lead-acid and gel batteries via the built-in display. However, to be able to set charging profiles for AGM and lithium batteries, either the optional display or the app is required. The optional Bluetooth dongle is required to use the app. Technical data: Battery voltage 12/24 V Rated charge current 10 A Nominal PV power 12 V: 160 W 24 V: 320 W Maximum open circuit PV voltage 45 V Operating temperature -25 to +50 °C Maximum efficiency 97.9 % Self-consumption 13 mA Charge algorithm 4-stage Load current 10 A Power terminals 4 mm² Protection category IP33 (housing) Dimensions (h x w x d) 175 x 143 x 48 mm Weight 0.57 kg Standards EN/IEC 62109-1, EN61000-6-3/EN61000-6-1, 47 CFR Part 15, Subpart B, IEC62509, IEC62321-3-1 In-line fuse holder: In-line fuse holder with protective cap for ATC or ATO type flat plug fuses. When the cap is attached the fuse holder is protected against dust and water jets (IP55 standard). Supplied with cable (approx. 26 cm) that forms a ring from one side of the fuse holder to the other and must be cut through and stripped as required for the installation of cable lugs or (crimp) connectors. Includes: 15 A fuse.

VICTRON

The SmartSolar maximises energy harvest and intelligently redirects it so that your battery is fully charged in the shortest possible time. It works by ensuring that all energy is taken from your solar panels and stores it in your batteries. This is especially useful on overcast days when the light intensity is constantly changing. The SmartSolar automatically detects the battery voltage and is suitable for a wide range of battery voltages. In addition, the 15/20 A versions offer load balancing via a physical output. The controller also has a programmable charging algorithm, internal temperature sensor, VE.Direct connection for connecting to a PC and Bluetooth. Technical data Battery voltage 12/24 V Rated charge current 15 A Nominal PV power 12 V: 220 W 24 V: 440 W Maximum open circuit PV voltage 100 V Operating temperature -30 to +60 °C Automatic load cut-off Yes Maximum efficiency 98% Self-consumption 12 V: 25 mA 24 V: 15 mA Charge voltage 'absorption' 14.4 V / 28.8 V Charge voltage 'float' 13.8 V / 27.6 V Charge algorithm Multistage, adaptive load current 15 A Protection Reverse polarity on battery (fuse) Output short circuit Overtemperature Power terminals 6 mm² Protection category IP43 (electronic components) IP22 (connection area) Dimensions (h x w x d) 100 x 113 x 50 mm Weight: 0.6 kg Standards EN/IEC 62109-1, UL 1741, CSA C22.2

VICTRON

The SmartSolar maximises energy harvest and intelligently redirects it so that your battery is fully charged in the shortest possible time. It works by ensuring that all energy is taken from your solar panels and stores it in your batteries. This is especially useful on overcast days when the light intensity is constantly changing. The SmartSolar automatically detects the battery voltage and is suitable for a wide range of battery voltages. In addition, the 15/20 A versions offer load balancing via a physical output. The controller also has a programmable charging algorithm, internal temperature sensor, VE.Direct connection for connecting to a PC and Bluetooth. Technical data Battery voltage 12/24 V Rated charge current 20 A Nominal PV power 12 V: 290 W 24 V: 580 W Maximum open circuit PV voltage 100 V Operating temperature -30 to +60 °C Automatic load cut-off Yes Maximum efficiency 98% Self-consumption 12 V: 25 mA 24 V: 15 mA Charge voltage 'absorption' 14.4 V / 28.8 V Charge voltage 'float' 13.8 V / 27.6 V Charge algorithm Multistage, adaptive load current 20 A Protection Reverse polarity on battery (fuse) Output short circuit Overtemperature Power terminals 6 mm² Protection category IP43 (electronic components) IP22 (connection area) Dimensions (h x w x d) 100 x 113 x 60 mm Weight: 0.65 kg Standards EN/IEC 62109-1, UL 1741, CSA C22.2

VICTRON

The SmartSolar maximises energy harvest and intelligently redirects it so that your battery is fully charged in the shortest possible time. It works by ensuring that all energy is taken from your solar panels and stores it in your batteries. This is especially useful on overcast days when the light intensity is constantly changing. The SmartSolar automatically detects the battery voltage and is suitable for a wide range of battery voltages. The SmartSolar MPPT charge controller provides comprehensive protection for electronic components, such as overheating protection and load reduction at high temperatures, your PV system is protected against PV short circuit and PV reverse polarity, and the solar charge controller also has PV reverse current protection. Technical data Battery voltage 12/24 V Rated charge current 30 A Nominal PV power 12 V: 440 W 24 V: 880 W Maximum open circuit PV voltage 100 V Operating temperature -30 to +60 °C Automatic load cut-off Yes Maximum efficiency 98% Self-consumption 12 V: 30 mA 24 V: 20 mA Charge voltage 'absorption' 14.4 V / 28.8 V Charge voltage 'float' 13.8 V / 27.6 V Charge algorithm Multistage, adaptive Max. PV short circuit current 35 A Protection PV reverse polarity Output short circuit Over temperature Power terminals 16 mm² / AWG6 Protection category IP43 (electronic components) IP22 (connection area) Dimensions (h x w x d) 130 x 183 x 70 mm Weight: 1.3 kg Standards EN/IEC 62109-1, UL 1741, CSA C22.2

VICTRON

The SmartSolar maximises energy harvest and intelligently redirects it so that your battery is fully charged in the shortest possible time. It works by ensuring that all energy is taken from your solar panels and stores it in your batteries. This is especially useful on overcast days when the light intensity is constantly changing. The SmartSolar automatically detects the battery voltage and is suitable for a wide range of battery voltages. The SmartSolar MPPT charge controller provides comprehensive protection for electronic components, such as overheating protection and load reduction at high temperatures, your PV system is protected against PV short circuit and PV reverse polarity, and the solar charge controller also has PV reverse current protection. Technical data Battery voltage 12/24 V Rated charge current 50 A Nominal PV power 12 V: 700 W 24 V: 1400 W Maximum open circuit PV voltage 100 V Operating temperature -30 to +60 °C Automatic load cut-off Yes Maximum efficiency 98% Self-consumption 12 V: 30 mA 24 V: 20 mA Charge voltage 'absorption' 14.4 V / 28.8 V Charge voltage 'float' 13.8 V / 27.6 V Charge algorithm Multistage, adaptive Max. PV short circuit current 60 A Protection PV reverse polarity Output short circuit Over temperature Power terminals 16 mm² / AWG6 Protection category IP43 (electronic components) IP22 (connection area) Dimensions (h x w x d) 130 x 183 x 70 mm Weight: 1.3 kg Standards EN/IEC 62109-1, UL 1741, CSA C22.2

VICTRON

The SmartSolar maximises energy harvest and intelligently redirects it so that your battery is fully charged in the shortest possible time. It works by ensuring that all energy is taken from your solar panels and stores it in your batteries. This is especially useful on overcast days when the light intensity is constantly changing. The SmartSolar automatically detects the battery voltage and is suitable for a wide range of battery voltages. The controller also has a programmable charging algorithm, internal temperature sensor, VE.Direct connection for connecting to other Victron devices or a PC, and Bluetooth. Technical data Battery voltage 12/24/48 V Rated charge current 35 A Nominal PV power 12 V: 500 W 24 V: 1000 W 48 V: 2000 W Maximum open circuit PV voltage 150 V Operating temperature -30 to +60 °C Maximum efficiency 98% Self-consumption 12 V: 20 mA 24 V: 15 mA 48 V: 10 mA Charge voltage 'absorption' 14.4 V / 28.8 V / 57.6 V Charge voltage 'float' 13.8 V / 27.6 V / 55.2 V Charge algorithm Multistage, adaptive Protection Reverse polarity on battery (fuse) PV reverse polarity Output short circuit Over temperature Power terminals 16 mm² Protection category IP43 (electronic components) IP22 (connection area) Dimensions (h x w x d) 130 x 186 x 70 mm Weight: 1.25 kg Standards EN/IEC 62109-1, UL 1741, CSA C22.2

VICTRON

The SmartSolar maximises energy harvest and intelligently redirects it so that your battery is fully charged in the shortest possible time. It works by ensuring that all energy is taken from your solar panels and stores it in your batteries. This is especially useful on overcast days when the light intensity is constantly changing. The SmartSolar automatically detects the battery voltage and is suitable for a wide range of battery voltages. The controller also has a programmable charging algorithm, internal temperature sensor, VE.Direct connection for connecting to other Victron devices or a PC, and Bluetooth. Technical data Battery voltage 12/24/48 V Rated charge current 45 A Nominal PV power 12 V: 650 W 24 V: 1300 W 48 V: 2600 W Maximum open circuit PV voltage 150 V Operating temperature -30 to +60 °C Maximum efficiency 98% Self-consumption 12 V: 20 mA 24 V: 15 mA 48 V: 10 mA Charge voltage 'absorption' 14.4 V / 28.8 V / 57.6 V Charge voltage 'float' 13.8 V / 27.6 V / 55.2 V Charge algorithm Multistage, adaptive Protection Reverse polarity on battery (fuse) PV reverse polarity Output short circuit Over temperature Power terminals 16 mm² Protection category IP43 (electronic components) IP22 (connection area) Dimensions (h x w x d) 130 x 186 x 70 mm Weight: 1.25 kg Standards EN/IEC 62109-1, UL 1741, CSA C22.2

VICTRON

The SmartSolar maximises energy harvest and intelligently redirects it so that your battery is fully charged in the shortest possible time. It works by ensuring that all energy is taken from your solar panels and stores it in your batteries. This is especially useful on overcast days when the light intensity is constantly changing. The SmartSolar automatically detects the battery voltage and is suitable for a wide range of battery voltages. The controller also has a programmable charging algorithm, internal temperature sensor, VE.Direct connection for connecting to other Victron devices or a PC, and Bluetooth. Keep an eye on all the important data of your PV system and plug the optional Smart-Control Display directly into the Smart Solar MPPT 150/60-TR charge controller. Technical specifications Battery voltage 12/24/48 V Rated charge current 60 A Nominal PV power 12 V: 860 W 24 V: 1720 W 48 V: 3440 W Maximum open circuit PV voltage 150 V Operating temperature -30 to +60 °C Maximum efficiency 98% Self-consumption 12 V: 35 mA 48 V: 20 mA Charge voltage 'absorption' 14.4 V / 28.8 V / 57.6 V Charge voltage 'float' 13.8 V / 27.6 V / 55.2 V Charge algorithm Multistage, adaptive Protection Reverse polarity on battery (fuse) PV reverse polarity Output short circuit Over temperature Power terminals 35 mm² Protection category IP43 (electronic components) IP22 (connection area) Dimensions (h x w x d) 185 x 250 x 95 mm Weight: 1.25 kg Standards EN/IEC 62109-1, UL 1741, CSA C22.2

VICTRON

The SmartSolar maximises energy harvest and intelligently redirects it so that your battery is fully charged in the shortest possible time. It works by ensuring that all energy is taken from your solar panels and stores it in your batteries. This is especially useful on overcast days when the light intensity is constantly changing. The SmartSolar automatically detects the battery voltage and is suitable for a wide range of battery voltages. The controller also has a programmable charging algorithm, internal temperature sensor, VE.Direct connection for connecting to other Victron devices or a PC, and Bluetooth. Keep an eye on all the important data of your PV system and plug the optional Smart-Control Display directly into the Smart Solar MPPT 150/70-TR charge controller. Technical specifications Battery voltage 12/24/48 V Rated charge current 70 A Nominal PV power 12 V: 1000 W 24 V: 2000 W 48 V: 4000 W Maximum open circuit PV voltage 150 V Operating temperature -30 to +60 °C Maximum efficiency 98% Self-consumption 12 V: 35 mA 48 V: 20 mA Charge voltage 'absorption' 14.4 V / 28.8 V / 57.6 V Charge voltage 'float' 13.8 V / 27.6 V / 55.2 V Charge algorithm Multistage, adaptive Protection Reverse polarity on battery (fuse) PV reverse polarity Output short circuit Over temperature Power terminals 35 mm² Protection category IP43 (electronic components) IP22 (connection area) Dimensions (h x w x d) 185 x 250 x 95 mm Weight: 1.25 kg Standards EN/IEC 62109-1, UL 1741, CSA C22.2

VICTRON

The SmartSolar maximises energy harvest and intelligently redirects it so that your battery is fully charged in the shortest possible time. It works by ensuring that all energy is taken from your solar panels and stores it in your batteries. This is especially useful on overcast days when the light intensity is constantly changing. The SmartSolar automatically detects the battery voltage and is suitable for a wide range of battery voltages. In addition, the 15/20 A versions offer load balancing via a physical output. The controller also has a programmable charging algorithm, internal temperature sensor and Bluetooth. Technical data Battery voltage 12/24 V Rated charge current 15 A Nominal PV power 12 V: 220 W 24 V: 440 W Maximum open circuit PV voltage 75 V Operating temperature -30 to +60° C Automatic load cut-off Yes Maximum efficiency 98% Self-consumption 12 V: 25 mA 24 V: 15 mA Charge voltage 'absorption' 14.4 V / 28.8 V Charge voltage 'float' 13.8 V / 27.6 V Charge algorithm Multistage, adaptive load current 15 A Protection Reverse polarity on battery (fuse) Output short circuit Overtemperature Power terminals 6 mm² Protection category IP43 (electronic components) IP22 (connection area) Dimensions (h x w x d) 100 x 113 x 40 mm Weight: 0.5 kg Standards EN/IEC 62109-1, UL 1741, CSA C22.2 System example: The following system example is based on a battery capacity of 300 Ah (2x 100 Ah consumer battery and 1x 100 Ah starter battery).